MotherBoardMonitor
Добавлено: 03 сен 2003 22:50Новая версия моего (и не только ;) ) горячё любимого "железного" мониторига (В сети вроде пока нету):
Самая свежая версия:
ftp://possum.ints.ru/-=SoftWARE=-/-=Har ... BM5351.EXE
Более ранние версии:
ftp://possum.ints.ru/-=SoftWARE=-/-=HardWare_Monitoring=-/Mbmonitor/MBM-New/mbm5340.exe
* added:
o Winbond W83647HF (thank you Winbond)
o Increased support for the EPIA boards (VT1211) thank you VIA Germany and ACME.de
o Configuration wizard, the reason for the increase in size of the d/l
o Special dump on the system info tab used to add your board to the config wizard for other users.
o wm_pause and wm_resume message (see help file advanced - messages)
o Priority function added to the starter.dll
o SetPath function added to the starter.dll in case you plan on running it as a service and it has no access to HKEY_CURRENT_USER in the reg.
o 2nd CPU temp on GA-7DPXDW+ which uses 1 LM90 for 2 CPU's (big thanks to Tim South for keeping at it)
o templist.ini added, with this you can enter your own temp table, see the help file advanced section
* Fixes:
o installer would always recommend C:\program files even if your program files was on another drive, this should be fixed
o autohide dashboard did not always work 100% when you had the dashboard set to start with MBM
o problem with e-mail test button
o dual monitor and OSD, the slided will now allow you to select a position on the left monitor
o problem with ADM1030 fan speed (Charles Xuereb)
o the LPC47xxx group of fans should respond better to the do not reset sensor chip option
o ITE range of sensors fan sensor 3 dividor problem fixed (thanks Anthony Smith)
* Changes:
o installer offers to start MBM after install
o installer will offer (checked) to start the help file if it's a new install
o installer will offer (unchecked) to start the help file if it's an update install
o ICH4-M auto enabled
o English language file (thanks Wesley Chung)
o fantemplist.ini has been changed, you now need to make a file for each fan you want to base a a temp sensor on, so fantemplist1.ini if you want to use fan1, fantemplist2.ini if you want to use fan 2
o fantemplist increased to 16
* Voltage.ini
o GA-8IPE1000Pro
o SOYO DRAGON KT400 (VTech)
o GA-8KNXP (MeanGene)
o EPoX 8RDA/8RDA (Valery Shatunov)
o Elite L7S7A2 (Willem Schaaij)
o Biostar M7VIG PRO (Chris Christo)
o Asus A7V8X-X (Willem Schaaij)
Самая свежая версия:
ftp://possum.ints.ru/-=SoftWARE=-/-=Har ... BM5351.EXE
Более ранние версии:
ftp://possum.ints.ru/-=SoftWARE=-/-=HardWare_Monitoring=-/Mbmonitor/MBM-New/mbm5340.exe
* added:
o Winbond W83647HF (thank you Winbond)
o Increased support for the EPIA boards (VT1211) thank you VIA Germany and ACME.de
o Configuration wizard, the reason for the increase in size of the d/l
o Special dump on the system info tab used to add your board to the config wizard for other users.
o wm_pause and wm_resume message (see help file advanced - messages)
o Priority function added to the starter.dll
o SetPath function added to the starter.dll in case you plan on running it as a service and it has no access to HKEY_CURRENT_USER in the reg.
o 2nd CPU temp on GA-7DPXDW+ which uses 1 LM90 for 2 CPU's (big thanks to Tim South for keeping at it)
o templist.ini added, with this you can enter your own temp table, see the help file advanced section
* Fixes:
o installer would always recommend C:\program files even if your program files was on another drive, this should be fixed
o autohide dashboard did not always work 100% when you had the dashboard set to start with MBM
o problem with e-mail test button
o dual monitor and OSD, the slided will now allow you to select a position on the left monitor
o problem with ADM1030 fan speed (Charles Xuereb)
o the LPC47xxx group of fans should respond better to the do not reset sensor chip option
o ITE range of sensors fan sensor 3 dividor problem fixed (thanks Anthony Smith)
* Changes:
o installer offers to start MBM after install
o installer will offer (checked) to start the help file if it's a new install
o installer will offer (unchecked) to start the help file if it's an update install
o ICH4-M auto enabled
o English language file (thanks Wesley Chung)
o fantemplist.ini has been changed, you now need to make a file for each fan you want to base a a temp sensor on, so fantemplist1.ini if you want to use fan1, fantemplist2.ini if you want to use fan 2
o fantemplist increased to 16
* Voltage.ini
o GA-8IPE1000Pro
o SOYO DRAGON KT400 (VTech)
o GA-8KNXP (MeanGene)
o EPoX 8RDA/8RDA (Valery Shatunov)
o Elite L7S7A2 (Willem Schaaij)
o Biostar M7VIG PRO (Chris Christo)
o Asus A7V8X-X (Willem Schaaij)